CAB Apollo 1 Uživatelský manuál Strana 1

Edition 10/99Apollo 1 / Apollo 2 / Apollo 3Quick Operator's Guide

ENG-9cab - Produkttechnik GmbHControl PanelThe front control panel of the Apollo is fitted with 4 function keys with indicatorLEDs, and a 2x16 charac

cab - Produkttechnik GmbHENG-10Function of the KeysThe function of the keys is dependent on the System Mode of the printer :System Mode ONLINESystem M

ENG-11cab - Produkttechnik GmbHFF key Provides label feed. The leading edge of the next label to beprinted is in print position.CAN key short pressin

cab - Produkttechnik GmbHENG-12Self TestPower On System TestWhen switched on, the Apollo automatically performs an internal system test.If the test is

ENG-13cab - Produkttechnik GmbHExplanation of the Self Test PrintoutFirmware-VersionSetup and statusinformationenAvailablefontsTest patternBar code wi

cab - Produkttechnik GmbHENG-14Monitor Mode/ ASCII Dump ModeIf programming directly, the monitor mode provides a method to print controlsequences whic

ENG-15cab - Produkttechnik GmbHSetupUsing the setup mode, the configuration of the Apollo may be customized to suitspecific requirements. Initial set

cab - Produkttechnik GmbHENG-16Overview of the Setup ParametersCountry Country setting : LCD display languageFormats of date and timeMeasuring unit (

ENG-17cab - Produkttechnik GmbHVersion xxxxx xxx m / xxx hPrinter info The parameter provides information about the firmware, the cumulativelength of

cab - Produkttechnik GmbHENG-18Safety InstructionsThe printer must be powered OFF before mounting the rewinder.During operation, the rotating axle is

ENG-1cab - Produkttechnik GmbHEU - Conformity DeclarationWe declare herewith that as a result of the manner in which the machine designated below wasd

ENG-19cab - Produkttechnik GmbHMounting the Printer AdapterIn order to operate the external rewinder, an adapter unit has to be mounted on tothe Apoll

cab - Produkttechnik GmbHENG-20Set the switch (5) to the required method of rewinding :- Rewind with labels on the outer side of the silicon liner- Re

ENG-21cab - Produkttechnik GmbHRewinding Operation1. Attach the rewinder to the Apollo by positioning the metal posts on the bottomof the rewinder (5)

cab - Produkttechnik GmbHENG-22Rewind Guide PlateThe optional rewind guide plate for printers with internal rewinder allows you torewind small print j

ENG-23cab - Produkttechnik GmbHThe Apollo is delivered with the tear-off plate (5) installed.Before mounting the cutter, the tear-off plate has to be

cab - Produkttechnik GmbHENG-24Montage des Spendesensors43 5 621FPresent SensorThe optional present sensor in connection with printers with internal r

ENG-25cab - Produkttechnik GmbHF1314151617187 8 9 10 111920612Inserting the Labels for Peel-off1. Lift the printhead by turning the lever (7) clockwis

cab - Produkttechnik GmbHENG-26Cut-/Peel-off AdapterBy using the cut/peel-off adapter it is possible, to operate the Apollo with cutterassembly or pre

ENG-27cab - Produkttechnik GmbHF1. Switch OFF the printer.2. Connect the 15-pin SUB-D plug (2) at the back side of the cut/peel-offadapter (1) to the

cab - Produkttechnik GmbHENG-28Memory CardsThe printers of the Apollo series provide an option for using memory cards topermanently save graphics, fon

cab - Produkttechnik GmbHENG-21 - Display2 - Function keys withindicator LEDs3 - Cover4 - Ribbon shield5 - Tear-off plate6 - Peripheral port7 - Printh

ENG-29cab - Produkttechnik GmbHPrinting from a Memory CardUsing a memory card provides the opportunity to print without a connectionof the Apollo to a

cab - Produkttechnik GmbHENG-30Keyboard AdapterThe keyboard adapter option offers to connect the Apollo to a standard PCkeyboard or any other compatib

ENG-31cab - Produkttechnik GmbHKey AssignmentThe Apollo can easily be adjusted to the keyboard configuration of the particularcountry by using the set

cab - Produkttechnik GmbHENG-32Error Messages/ Problem SolutionThe Apollo is equipped with a comprehensive self diagnostic system which willindicate e

ENG-3cab - Produkttechnik GmbH124312345656Connecting the PrinterConnection to Power SupplyThe Apollo is designed for use with 230V A.C/ 50Hz (standard

cab - Produkttechnik GmbHENG-4Print MediaThe Apollo can be operated in direct thermal as well as thermal transfer mode.For direct thermal mode, only u

ENG-5cab - Produkttechnik GmbHLoading Labels1 2 3 4 56789 10111. Open the cover.2. Lift the printhead by rotating the lever (1) clockwise until it sto

cab - Produkttechnik GmbHENG-6Loading Transfer Ribbon76421154321. Open the cover.2. To lift the printhead, turn the printhead lever (1) clockwise unti

ENG-7cab - Produkttechnik GmbHAdjustments Concerning the LabelsThe printer can use a variety of media widths an thicknesses.Beside it is possible to u

cab - Produkttechnik GmbHENG-8Adjustment of the Label Edge SensorTo accommodate a variety of print jobs, the position of the label edge sensor (1)can